EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This Mount does not fit: Smith & Wesson M&P C.O.R.E Series (Already optics ready) Smith & Wesson M&P Shield EZ .380 Smith & Wesson M&P .22 Compact Smith & Wesson SW9VE Smith & Wesson SW40VE
Montura perfecta para tu Vortex Viper/Venom en tu S&W M&P
La montura S&W M&P VORTEX VIPER/VENOM de EGW está diseñada para facilitar la instalación de tus miras rojas. Aquí tienes todo lo que necesitas saber:
Descripción del producto
Las miras rojas EGW están destinadas a ser instaladas de izquierda a derecha (con la boca del cañón hacia adelante). La dovetail tiene un ángulo progresivo que permite una instalación más sencilla. Simplemente retira la mira trasera de tu arma y reemplázala con la montura EGW para poder instalar tu Vortex Viper/Venom, Burris FastFire o Docter.
La montura se puede quitar y reemplazar con tu mira trasera en cualquier momento. Se incluye el hardware de montaje.
Instrucciones de instalación
- Retira la mira trasera*
- Instala la montura EGW en la dovetail
- Ajusta el tornillo de fijación (si aplica)
- Coloca la mira roja sobre la montura EGW (colocar un pequeño trozo de papel entre la mira roja y la montura facilitará su retirada y evitará que el Loctite se adhiera a la mira roja).
- Aplica Loctite azul a los tornillos de montaje proporcionados
- Aprieta los tornillos de montaje a 15 in/lbs
Incluye:
- 2 tornillos de cabeza de botón - Proporcionados para las miras Vortex Viper y Venom
- 2 tornillos de cabeza plana - Proporcionados para las miras Burris FastFire y Docter
Los tornillos incluidos con esta montura requieren una llave Allen de 5/64'' para la instalación.
La modificación de tu arma de fuego puede anular la garantía del fabricante.
Este producto debe ser instalado y revisado por un armero calificado.
No se expresa ni se implica ninguna responsabilidad por daños o lesiones que puedan resultar de una instalación o uso incorrecto de este producto.
Esta montura no es compatible con:
- Smith & Wesson M&P C.O.R.E Series (ya lista para ópticas)
- Smith & Wesson M&P Shield EZ .380
- Smith & Wesson M&P .22 Compact
- Smith & Wesson SW9VE
- Smith & Wesson SW40VE